|
T-SHAPED
STRUCTURAL RAIL
A level rail is
important. We place
leveling screws on
both sides of the
rail. It is then
precisely leveled
and under filled
with grout to form a
concrete-like strong
base. Each track
joins together
perfectly, like a
model train. The
rails are end
drilled to accept a
3/8" steel pin. The
result: Systems that
move smoothly and
silently. Our
standard rail is 1
1/2" high and
2 1/2"
wide.
DECK AND RAMP
A Jeter deck feels
solid, like the
floor underneath it.
Decks are made of
tongue and groove,
3/4" plywood.
Leveling screws are
placed 16" apart,
which makes our
decks adjustable to
most any floor
condition. All edges
are finished, and
the deck arrives
ready to receive the
covering of your
choice.
 |
|
CENTER DRIVE, CROSS
OVER CHAIN
We also use a cross
over chain to
connect the two
drive shafts. This
chain is a much
heavier, Harley
Davidson size chain.
It transfers power
to the drive line,
which moves all
wheels on one side
of the carriage. By
driving the system
at the carriage
center, we achieve
perfect, uniform
back and forth
motion. All
sprockets are welded
securely to the 1"
solid steel shafts.
The shafts are
supported by
heavy-duty pillow
block bearings,
rated at 1,800 lbs
each. We have
installed over
10,000 systems. Our
mobile systems are
designed for
long-lasting
reliability.
WELDED CARRIAGE
FRAME
Our strong,
ladder-shaped
carriage frame is
designed to support
a maximum weight
load of 1,100 lbs
per carriage foot.
Our systems roll
easily due to the
precise squareness
of the carriage. The
frame parts are
clamped to a unique
fixture, then welded
to a tolerance
within thousandths
of an inch. Each
carriage is designed
from 12-gauge, .110"
thick 1008/1010 AISI
steel.
RECESSED LIP
SAFELY SECURES
CABINETS
Jeter carriages
provide recessed
lips to contain
shelving within the
structure of the
carriage. This
secures the
shelving, so that it
cannot shift during
carriage movement.
Other manufacturers
offer carriages
where shelving "just
sits" on top. With
Jeter, you’ll
receive a system
that offers superior
quality, safety and
reliability.
SERVICE-FREE
CHAIN DRIVE SYSTEM
All systems come
with a unique,
patented automatic
chain tensioner. It
adjusts and
compensates for
chain stretch. This
chain tensioner is a
key component to
ensure your Jeter
system will remain
service-free –– for
the life of the
system.
CARRIAGES ROLL
EFFORTLESSLY
Each Jeter mobile
system is carefully
designed. We analyze
the weight that will
be placed on the
carriages and assign
the proper gear
ratio. Our systems
roll on 5" drive
wheels, and guidance
is provided by
flanged wheels at
both ends of the
system. All center
position wheels are
flat. Our systems
move thousands of
pounds with truly
finger-tip effort.
An average system
moves 6,000 lbs with
1 lb of effort at
the handle –– it’s
easy.
VARIETY OF END
PANEL COLORS
End panels are
offered in a variety
of colors. The
quality appearance
will compliment your
office decor. And,
the end panels close
leaving a 3/4" gap
so that fingers
cannot get injured.
We design our
systems making
safety first,
always. SAFETY
BRAKES Our reliable
safety brake is
activated by a knob
above the handle.
Safety brakes are
installed on
carriages 12" or
longer and on all
x-ray systems. It is
optional on all
other systems.
STATIONARY
CARRIAGES BOLTED TO
RAIL
Stationary units are
an integral part of
each Jeter mobile
system. When a
carriage abruptly
hits a stationary
unit, thousands of
pounds of energy
must be absorbed.
Our stationary units
are firmly bolted to
the rail, which is
secured to the
floor. This
guarantees the
perfect positioning
of rails at the time
of installation.
QUALITY
INSTALLATIONS
ELIMINATE SERVICE
CALLS
All systems are
thoroughly reviewed
at our factory prior
to shipment. Each
piece is marked for
correct placement
during installation.
All hardware for
assembly is
provided, including
carpet trim to have
the system look
perfect. And,
installations are
completed by
experienced,
factory-trained
service technicians. |
